Back to all FORScan mods
Advanced FORScan Mod

Heated Steering Wheel Icon on Screen (2021+) FORScan Code for F-150

Your truck

Add Heated Steering Wheel Icon on Screen (2021+) to a worksheet

$9.99

Choose the year, trim, engine, and drivetrain. Nothing is filled in until you pick it.

Sample

Sample worksheet

Download sample PDF

This is a sample of the layout, not a worksheet for your truck. The paid sheet uses the mods you pick and leaves a blank for each original value. You write any change yourself in FORScan.

Sample rows for a 2021 F-150. These are 2021+ addresses. Auto Start/Stop is not in this sample.

ModuleAddressYour original valueTarget valueNotes
BCM726-39-02____________xxx0 xxxx xx--Sample layout. 2021+ Bambi Mode.
ACM727-01-01____________xxxx xxxx 0x--Sample layout. 2021+ Fake Engine Noise.
BCM726-63-02____________xxx0 xxxx xx--Sample layout. 2021+ Double Horn Honk Disable.

Sample rows only. A purchased worksheet is built from your year, trim, engine, drivetrain, and selected mods. Worksheet purchases are non-refundable except where required by law.

Heated Steering Wheel Icon on Screen (2021+) is an advanced change that rewards careful backups for 2021–2026 Ford F-150 trucks, applied with FORScan over an OBD-II adapter. Shows heated steering wheel control on the Sync 4/4A climate bar. It is fully reversible and typically takes about 10 minutes to write once your worksheet is in hand.

The change touches the Accessory Protocol Interface Module (SYNC) (APIM), and your F-Config worksheet lists all 3 as-built code rows with the module, address, and target value. Each row includes a blank for your original value so you can back up before writing changes and roll back later. Quick access to heated wheel from the home screen.

Why F-150 owners use it

Quick access to heated wheel from the home screen

Worksheet rows

3

Modules

1

Estimated time

~10 min

Compatibility

2021-2026

How you'll apply Heated Steering Wheel Icon on Screen (2021+)

The DIY process from start to finish — backup-first and, where possible, reversible.

1

Back up your originals first

Before changing anything, use FORScan to read and record the current value of each of the 3 rows in the Accessory Protocol Interface Module (SYNC) (APIM). Your worksheet leaves a blank beside every row for exactly this.

2

Write the worksheet values

Enter the 3 target rows from your worksheet one at a time. Most owners finish Heated Steering Wheel Icon on Screen (2021+) in about 10 minutes with a laptop and a FORScan-compatible OBD-II adapter.

3

Cycle the ignition and verify

Turn the key off and back on, then confirm the change behaves as expected before moving on. If anything looks off, stop and compare against the originals you recorded.

4

Roll back anytime

Because Heated Steering Wheel Icon on Screen (2021+) is fully reversible, you can put every original value back later and return to stock whenever you want.

Compatible F-150 years

Review year-specific FORScan worksheet context before adding this mod to your build.

Before you write values

Make backups, confirm the adapter can see the truck, and review the FAQ before applying worksheet values.

Printable worksheet preview

Customers get a clean worksheet with original-value blanks, target values, completion checks, and module notes.

ModuleAddressTarget valueNotes
APIM7D0-02-03xxxx xxx1 xx--Step 1 (prerequisite): Enable the Unreal Sync theme
APIM7D0-02-02xx2x xxxx xx--Step 2 (prerequisite): Enable the climate bar - use 2 for non-hybrid, 6 for hybrid
APIM7D0-02-01xxxx xxx1 xx--Step 3: Heated Steering Wheel (HSW) Available. Add 1 (hex) to the current nibble value while preserving the other packed bits (Climate Front Zones / Smart Auto / Rear Climate) — e.g. if default is 0, use 1; if default is 4, use 5.

Risk and safety notes

Requires careful backups and confidence working in FORScan.

Multi-step: requires the Unreal theme + climate bar to be enabled first (steps 1-2) before the icon will show at all. Skip steps 1-2 if already applied via another 2021+ climate-bar mod (e.g. heated-cooled-seat-icons-2021) on the same truck. Different address and UI than the 2015-2020 version.

Required modules

Accessory Protocol Interface Module (SYNC) (APIM)

Heated Steering Wheel Icon on Screen (2021+) FORScan FAQ

Is Heated Steering Wheel Icon on Screen (2021+) safe to do on my F-150?

It is rated advanced. It is well within reach for a careful DIYer, but back up your original values and work through the worksheet one row at a time.

Is Heated Steering Wheel Icon on Screen (2021+) reversible?

Yes. This change is fully reversible as long as you record your original as-built values first. Your worksheet leaves a blank for each original value so you can roll back to stock.

Which modules does Heated Steering Wheel Icon on Screen (2021+) change?

It writes 3 code rows to the Accessory Protocol Interface Module (SYNC) (APIM). Each row is listed in your worksheet with its address and target value.

How long does Heated Steering Wheel Icon on Screen (2021+) take with FORScan?

Most owners finish Heated Steering Wheel Icon on Screen (2021+) in about 10 minutes once they have the worksheet, a laptop, and a FORScan-compatible OBD-II adapter.

What F-150 years does Heated Steering Wheel Icon on Screen (2021+) work on?

Heated Steering Wheel Icon on Screen (2021+) applies to 2021–2026 F-150 trucks. Compatibility can still vary by trim, package, and module software version, so confirm against your own as-built data.

Anything to watch out for with Heated Steering Wheel Icon on Screen (2021+)?

Multi-step: requires the Unreal theme + climate bar to be enabled first (steps 1-2) before the icon will show at all. Skip steps 1-2 if already applied via another 2021+ climate-bar mod (e.g. heated-cooled-seat-icons-2021) on the same truck. Different address and UI than the 2015-2020 version.

Related SYNC & Media mods

Other FORScan changes in the same category you can add to the same worksheet.