Advanced FORScan Mod

Intrusion Alarm Enable FORScan Code for F-150

Your truck

Add Intrusion Alarm Enable to a worksheet

$9.99

Choose the year, trim, engine, and drivetrain. Nothing is filled in until you pick it.

Add to worksheet: Intrusion Alarm Enable Build my worksheet — $9.99

YearTrimEngineDrivetrain

Sample

Sample worksheet

Download sample PDF

This is a sample of the layout, not a worksheet for your truck. The paid sheet uses the mods you pick and leaves a blank for each original value. You write any change yourself in FORScan.

Sample rows for a 2020 F-150. These are 2015-2020 addresses, not the 2021+ map.

Module	Address	Your original value	Target value	Notes
BCM	726-27-01	____________	xxxx xxx0 xxxx	Sample layout. 2015-2020 Bambi Mode.
ACM	727-01-01	____________	xxxx x0xx xxxx	Sample layout. 2015-2020 Fake Engine Noise.
BCM	726-41-02	____________	xxx0 xxxx xxxx	Sample layout. 2015-2020 Double Horn Honk Disable.

Sample rows only. A purchased worksheet is built from your year, trim, engine, drivetrain, and selected mods. Worksheet purchases are non-refundable except where required by law.

Intrusion Alarm Enable is an advanced change that rewards careful backups for 2015–2020 Ford F-150 trucks, applied with FORScan over an OBD-II adapter. Enables intrusion alarm support after adding intrusion sensors. It is fully reversible and typically takes about 10 minutes to write once your worksheet is in hand.

The change touches the Instrument Panel Cluster (IPC), and your F-Config worksheet lists all 1 as-built code row with the module, address, and target value. Each row includes a blank for your original value so you can back up before writing changes and roll back later. Supports an intrusion sensor retrofit on compatible trucks.

Why F-150 owners use it

Supports an intrusion sensor retrofit on compatible trucks

Worksheet rows

Modules

Estimated time

~10 min

Compatibility

2015-2020

How you'll apply Intrusion Alarm Enable

The DIY process from start to finish — backup-first and, where possible, reversible.

Back up your originals first

Before changing anything, use FORScan to read and record the current value of each of the 1 row in the Instrument Panel Cluster (IPC). Your worksheet leaves a blank beside every row for exactly this.

Write the worksheet values

Enter the 1 target row from your worksheet one at a time. Most owners finish Intrusion Alarm Enable in about 10 minutes with a laptop and a FORScan-compatible OBD-II adapter.

Cycle the ignition and verify

Turn the key off and back on, then confirm the change behaves as expected before moving on. If anything looks off, stop and compare against the originals you recorded.

Roll back anytime

Because Intrusion Alarm Enable is fully reversible, you can put every original value back later and return to stock whenever you want.

Compatible F-150 years

Review year-specific FORScan worksheet context before adding this mod to your build.

2015 F-150 2016 F-150 2017 F-150 2018 F-150 2019 F-150 2020 F-150

Before you write values

Make backups, confirm the adapter can see the truck, and review the FAQ before applying worksheet values.

Worksheet builder Backup original values Adapter guide FORScan will not connect How worksheets work Worksheet FAQ

Printable worksheet preview

Customers get a clean worksheet with original-value blanks, target values, completion checks, and module notes.

Module	Address	Target value	Notes
IPC	720-02-02	5xxx xx	Run BdyCM LIN New Module Initialization after writing

Risk and safety notes

Requires careful backups and confidence working in FORScan.

Only use when intrusion sensors have been added. Also works on the 4.2-inch cluster. This value also turns on rear park aid — if the truck has no rear parking sensors, record the original value first so you can back it out. Run BdyCM LIN New Module Initialization after writing.

Required modules

Instrument Panel Cluster (IPC)

Intrusion Alarm Enable FORScan FAQ

Is Intrusion Alarm Enable safe to do on my F-150?

It is rated advanced. It is well within reach for a careful DIYer, but back up your original values and work through the worksheet one row at a time.

Is Intrusion Alarm Enable reversible?

Yes. This change is fully reversible as long as you record your original as-built values first. Your worksheet leaves a blank for each original value so you can roll back to stock.

Which modules does Intrusion Alarm Enable change?

It writes 1 code row to the Instrument Panel Cluster (IPC). Each row is listed in your worksheet with its address and target value.

How long does Intrusion Alarm Enable take with FORScan?

Most owners finish Intrusion Alarm Enable in about 10 minutes once they have the worksheet, a laptop, and a FORScan-compatible OBD-II adapter.

What F-150 years does Intrusion Alarm Enable work on?

Intrusion Alarm Enable applies to 2015–2020 F-150 trucks. Compatibility can still vary by trim, package, and module software version, so confirm against your own as-built data.

Anything to watch out for with Intrusion Alarm Enable?

Related Cluster & Display mods

Other FORScan changes in the same category you can add to the same worksheet.